#Orbiter extruder wiring install#
#Orbiter extruder wiring driver#
#Orbiter extruder wiring download#

Now here is the thing: There are 4 wires. Me love computers, me not into electronic buildsīut OK, no problem, I’m a grown up, I committed to buy a 3D printer, I can do that. Seriously, I looked here and there, found out that it’s a commun wiring error for pre-assembled printers, I now “just have to” rewire the motor.

So the printer does everything good it seems, but there’s no plastic going out, so it produces an “air print” Instead of pushing the filament into the extruder, it pulls it. The issue is that when I try to print, the extruder motor goes backward. Pushing filament manually does extrude, no issue with temperatures at all. I recently bought the Afinity A9 3D printer from RobotShop ( ).Īssembled it, made the initial tuning, looks good. M201 X4000.00 Y4000.00 Z400.00 E600.00 C400.This is a 3D printer question, not sure the forum category I chose is correct. High precision direct drive extruder using custom made parts, manufactured by LDO Motors. Therefore, retraction speed needs to be limited in the slicer to. One of the most expected project of 2021, the Orbiter v2.0.

#Orbiter extruder wiring driver#

Having high step/mm ratio for the Orbiter v2.0, limits the maximum extrusion speed the Trinamic driver can drive the Orbiter to about 40mm/s. M350 X16 Y16 Z16 E16 I1 configure microstepping with interpolation Press in the 3010 axial fan in the middle with the fan wiring toward the left bottom side of the shroud (toward the wire guide part). M350 C8 I0 configure microstepping without interpolation M569 P4 S0 physical drive 4 goes backwards (Coupler) M569 P3 S1 physical drive 3 goes forwards (E0) M569 P2 S0 physical drive 2 goes backwards (Z axis) M569 P1 S1 physical drive 1 goes forwards (Y axis) M569 P0 S1 physical drive 0 goes forwards (X axis) I have tried different currents 1400mA, 1000mA, 900mA and 700mA but still doing the same. Retraction: 1.2mm (for the volcano V6 hotend) Maximum instantaneous speed change (jerk): 300 mm/min(RRF), 5 (Marlin) Stepps: 655 stepps / mm 16 micro-stepping (for the 7.5:1 gearing ratio) I have put the configuraton for the extruder as per instructions: I have also tried swapping the cables but is not working either. BOM Orbiter filament sensor kit (Buy the appropriate one for the version of the orbiter you have this guide is showing it with V1.5) Printed filament sensor housing (only applicable if your kit didn’t come with the SLS nylon part) Unboxing The contents of the kit varies depending on which version you buy. The Orbiter extruder really performed well in that scenario as it was still extruding. The connections are B, A, A, B on the duet, the same for my motor. Rat Rig provides a great wiring diagram for the wiring process. Nor the board has problem because for ease of practicing I have tried driver3 and driver0.

#Orbiter extruder wiring download#

I have bought 4 motors from Wantai (36BYGH218, 1.8A, 1.8deg/step)and tested them all, so I do not think it is the motor's problem, because they are all doing the same noise like ggrrrrr, loosing steps. The Orbiter v1.5 140g Dual Drive Direct Extruder by lorinczroby - Thingiverse Download files and build them with your 3D printer, laser cutter, or CNC. I know I have to change VREFs on the board and change eSteps, but other than that it seems like a straightforward install.

#Orbiter extruder wiring install#

Unfortunately I am having problems with the motor. Has anyone installed an Orbiter direct extruder : r/ender5plus Has anyone installed an Orbiter direct extruder I'm looking to install one and wanted to check if anyone else had done it. This is LDOs finest direct drive extruder system in which they. I have just instaled the new extruder, 'The orbiter', for minimizing the weight. High precision direct drive extruder using custom made parts, manufactured by LDO Motors.